count back number of bars

• 04/30/2018 at 12:50 PM #69460
  cummish

  Hi I am counting back bars

  eg lowest[8](low)

  this is on a 5 minute chart.  When I go to a 1 min chart I want the same length of time so multiplied 8 x 5 = 40min.

  But the value that it returns is different.  The only thing I can find that might be related is that on the minute charts there seems to be bars missing although if I hover over where they are they give a hi/lo/close so they do exist but seems like they are being skipped over when counting back the bars?  If I count the number of “missing” bars it seems to align with how much further it is extending back ie ignoring those mars

   

  Anyone experienced this and thoughts on overcoming? Thanks

  

  cummish

  Participant

  Topics: 6

  Replies: 10

  Been thanked: 0 times
  04/30/2018 at 1:44 PM #69467
  robertogozzi

  This is a “normal behaviour, since if you select 5-min bars from 10:25, down to 09:50 they are just 8 bars.

  If you select 40 1-minute bars from 10:25 down to 09:51 they are 40 bars, but not the same, since the 10:25 5-min bar actually closes at 10:29.

  From my pic you can easily spot the difference.

   

  

  robertogozzi

  Moderator

  Topics: 69

  Replies: 17150

  Been thanked: 4039 times
  04/30/2018 at 1:54 PM #69469
  robertogozzi

  In my pic I only selected 5 bars, from 14:05 through 14:25, that is only 21 1-minute bars displayed, since it starts counting backwards from 14:25. You’ll have to do some math to adjust a TF to another one when doing these tricks!

   

  

  robertogozzi

  Moderator

  Topics: 69

  Replies: 17150

  Been thanked: 4039 times
  05/11/2018 at 8:47 AM #70182
  cummish

  When I did the testing it seemed that it was the not displayed “missing” bars which there were a number on the minute char not just the difference of a 1 bar nuance

  

  cummish

  Participant

  Topics: 6

  Replies: 10

  Been thanked: 0 times
  05/11/2018 at 10:18 AM #70193
  robertogozzi

  To visualize the differenze you have to draw a RECTANGLE on the higher TF to highlight the desired time range, if you have set the option to display objects in lower TFs, you’ll notice if any bar in the lower TF is outside the rectangle or not.

  

  robertogozzi

  Moderator

  Topics: 69

  Replies: 17150

  Been thanked: 4039 times
  05/16/2018 at 8:11 AM #70568
  cummish

  I have also attached an example.

  the attached image shows the high and low from the bar highlighted back for 8 bars (indicator at the bottom)

  Yet the high on the indicator for that many bars actually goes three bars further back which is the same number of invisible/missing 1 min bars

  This is why I think it is ignoring them and going back too far.

   

  

  cummish

  Participant

  Topics: 6

  Replies: 10

  Been thanked: 0 times
  05/16/2018 at 8:59 AM #70583
  robertogozzi

  No pic attached!

   

  

  robertogozzi

  Moderator

  Topics: 69

  Replies: 17150

  Been thanked: 4039 times
  05/18/2018 at 1:48 AM #70730
  cummish

  Apologies – attached

  

  cummish

  Participant

  Topics: 6

  Replies: 10

  Been thanked: 0 times
  05/18/2018 at 7:32 AM #70737
  robertogozzi

  You should tell me:

  1. instrument used
  2. date and time of tha bar
  3. TF used

  and you should also highlight bars you are referencing.

  

  robertogozzi

  Moderator

  Topics: 69

  Replies: 17150

  Been thanked: 4039 times
• Author
  Posts